Electronics>FC / ESC Stacks>20mm x 20mm

SpeedyBee F405 Mini BLS 35A 20×20 Stack

5.00 out of 5
(5 customer reviews)

The SpeedyBee F405 miniStack – F405 + 35A BLS ESC features Bluetooth for Betaflight via phone app, onboard battery level indicators and more!

$124.99

In Stock at KiwiQuads

Ships from our Tauranga warehouse
SKU: 1865 Categories: ,

Description

Utilizing an upgraded F405 flight controller chip, it features a built-in Bluetooth chip for seamless wireless Betaflight tuning. The board comes with a 4-level battery voltage display, built-in barometer, and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs.

The 35A 4-in-1 BLHeliS Mini ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC.

Specs Overview

  • Product Name SpeedyBee F405 Mini BLS 35A 20×20 Stack
  • Flight Controller SpeedyBee F405 Mini
  • ESC SpeedyBee BLS 35A Mini V2 4-in-1 ESC
  • Bluetooth Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
  • WiFi NOT Supported
  • Wireless FC Firmware Flashing NOT Supported
  • Wireless Blackbox Dwonload & Analysis NOT Supported
  • Power Input 3-6S LiPo
  • Mounting 20 x 20mm 3.5mm hole size,Compatible with M2 and M3 screws/Silicone grommets
  • Dimension 32mm(L) x 35mm(W) x 14.2mm(H)
  • Weight 13.5g

Detailed Manual including wiring diagrams: SpeedyBee F405 Mini BLS 35A Stack – User Manual – EN

Specifications

  • ProductName SpeedyBee F405 Mini
  • MCU STM32F405
  • IMU(Gyro) ICM42688P
  • USB Port Type Type-C
  • Barometer Built-in
  • OSD Chip AT7456E chip
  • BLE Bluetooth Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
  • Wireless FC Firmware Flashing NOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmeare update
  • Wireless Blackbox Dwonload & Analysis NOT Supported. Please connect to the Betaflight configurator on the PC to do blackbox analysis.
  • WIFI Not supported
  • DJI Air Unit Connection Way Direct soldering
  • DJI Air Unit Compatibility Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input.
  • Blackbox 8MB Onboard Flash
  • BetaFlight Camera Control Pad Yes(CC pad on the front side)
  • Current Sensor Input Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.
    Power Input 3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin harness or G, V pads from the bottom side of the flight controller.
  • 5V Output 4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.
  • 9V Output 1 group of 9V output, one +9V pad on front side. The total current load is 3A.
  • 3.3V Output Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.
  • 4.5V Output Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
  • ESC Signal M1 – M4 wires or soldering pads on bottom side.
  • UART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
  • ESC Telemetry UART R5(UART5)
  • I2C Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc
  • Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LEDs controlled by the
  • Betaflight firmware.
  • Buzzer BZ+ and BZ- pad used for 5V Buzzer
  • BOOT Button Supported. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this
  • is for firmware flashing when the FC gets bricked.
  • RSSI Input Not Supported
  • Smart Port / F.Port Not Supported
  • Supported Flight Controller Firmware BetaFlight(Default), INAV
  • Firmware Target Name SPEEDYBEEF405MINI
  • Mounting 20 x 20mm 3.5mm hole diameter ,Compatible with M2 and M3 screws/Silicone grommets.
  • Dimension 30(L) x 32(W) x 7.8(H)mm
  • Weight 9.6g

 

  • ProductName SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
  • Firmware BLHeli_S J-H-40
  • Continuous Current 35A * 4
  • Burst Current 45A(5seconds)
  • ESC Protocol DSHOT300/600
  • Power Input 3-6S LiPo
  • Power Output VBAT(Battery voltage, used to power the flight controller)
  • Current Sensor Support (Scale=250 Offset=-500)
  • Mounting 20 x 20mm ∅3.5mm hole size,compatible with M2 and M3 screws/Silicone grommets.
  • Dimension 35 * 35 * 5.5mm
  • Weight 7.2g

 

 

Additional information

Brand

5 reviews for SpeedyBee F405 Mini BLS 35A 20×20 Stack

  1. 5 out of 5

    Juan Carlos (verified owner)

  2. 5 out of 5

    Juan Carlos (verified owner)

  3. 5 out of 5

    Graham (verified owner)

  4. 5 out of 5

    Julius (verified owner)

  5. 5 out of 5

    Antonius Scholte (verified owner)

    Tiny pads but works the charm!

Only logged in customers who have purchased this product may leave a review.